Yes, it’s worth refinishing hardwood floors instead of replacing them. Refinishing is cost-effective, it’s quicker, and it’s a lot easier because it requires less labor. A refinishing project takes less time and effort and, if done properly, can make old flooring look brand new.

Big scratches and dents, gray floorboards and splinters are all signs that your hardwood floors need refinishing. Refinishing hardwood floors can make old, worn surfaces look new again….

1. Major scratches and dents.
2. Cupping.
3. Splinters.
4. Gray floorboards.
5. Water stains.
6. Fading and discoloration.

approximately ten years

A solid hardwood plank at least 3/4 inches thick will likely need to be refinished four to six times during its total lifespan. It’s commonly accepted that you refinish every seven to ten years. Important note: some hardwood is only 1/4 inches thick. In this case, a refinish could strip away all traces of the floor.

If I had to pick an ideal time, I would say spring or fall when the indoor temperature is most consistent with outdoor temperature and it’s often easy to open the windows (after the work is complete) to help air out the smell faster. But, really, sanding and refinishing hardwood can take place any time of year.

According to HomeAdvisor, the typical price range to refinish hardwood floors is between $1,074 and $2,485, with the national average at $1,757. This comes out to $3 to $8 per square foot, including materials and labor. Roughly 80 percent of the cost to refinish hardwood floors comes from labor.

Cost per square foot to refinish hardwood floors:

In general, it will almost ALWAYS be less expensive to refinish your hardwood floors. If you replace them, you need to pay for additional wood as well as ripping up and hauling away existing hardwood. Even if you have this, it will still be less expensive then replacing the whole floor.

sandpaper

1. Step 1: Prepare the Floor for Refinishing “
2. Step 2: Pull Up the Shoe Base Moulding “
3. Step 3: Rough-Sand the Floor “
4. Step 4: Sand the Edges and Corners “
5. Step 5: Screen Sand the Floor “
6. Step 6: Remove All Dust “
7. Step 7: Apply the Wood Stain “
8. Step 8: Apply the Finish “

3 Approaches to Refinishing Hardwood Floors Without Sanding

1. Use a store-bought chemical abrasion kit.
2. Buff and recoat floors with polyurethane.
3. Use a revitalizer.

If your hardwood floors are scratched and dull, you can bring them back to their former beauty by refinishing them. One major drawback of refinishing wood floors is the dust that is produced. Cleanup after your floors have been sanded can also be a nightmare. …

Generally, it’s a good idea to remove baseboards before installing your flooring, here’s why: The finished product might look better. Usually, only the shoe molding is removed and re-installed (or replaced).

The best hardwood floor restorer

• Rejuvenate Professional Wood Floor Restorer is a non-toxic formula that seals and protects wood floors.
• Rejuvenate Professional Wood Floor Restorer.
• Weiman Hardwood Polish & Restorer.
• PRO SHOT Industrial Re-Newing Floor Restorer.

How to Revitalize Floors

1. First, give your floor a good cleaning.
2. Next, apply the revitalizer according to the package instructions.
3. Use your mop to spread the revitalizer on the floor.
4. Once the revitalizer is spread evenly, let it dry fully before you move furniture back in place or allow foot traffic on the floors.

1. Apply the All Floors Restorer evenly across the floor using a clean Microfiber Bonnet placed over a sponge mop.
2. Once you treat one section, move on to the next area of your floor.
3. Allow to dry for at least 45 minutes before walking on floor.

Vinegar is acidic, and it can strip away all types of finishes, therefore vinegar is not safe on hardwood floors. The same effect is possible when using ammonia, abrasive cleaning agents and alkaline-based products. Keep in mind that the use of some cleaning products could negate your flooring warranty.

Too Much Product If you use too much of the product on your flooring, it can build up and form that unsightly cloudy film.